Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 9 - Jul 14
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Kawasaki GASKET-SET11028-6195Don't compromise your engine rebuild with mismatched gaskets this genuine Kawasaki gasket set provides every seal needed for a complete, leak free overhaul. Compatibility FA series (verify your model number before purchasing) FC series FH series Important: Always verify your exact engine model number and serial number before purchasing. Kawasaki engine series share many part numbers but not all parts are interchangeable between variants. Part Details
Don't compromise your engine rebuild with mismatched gaskets — this genuine Kawasaki gasket set provides every seal needed for a complete, leak-free overhaul.
✅ Compatibility
- FA series (verify your model number before purchasing)
- FC series
- FH series
⚠️ Important: Always verify your exact engine model number and serial number before purchasing. Kawasaki engine series share many part numbers but not all parts are interchangeable between variants.
🛠️ Part Details
- OEM Part Number: 11028-6195
- Replaces: Verify with your Kawasaki dealer or engine manual
- Brand: Kawasaki — Genuine OEM
- Type: Original Equipment Manufacturer (OEM) replacement
⭐ Key Features
- Complete set covers all major engine sealing points
- Every gasket manufactured to OEM material specification
- Correct thickness for proper component clearances and compression
- Head gasket, cover gaskets, exhaust gasket and all seals included
- Single kit eliminates the risk of missing a critical seal
🔧 What Problem This Solves
- Multiple oil, fuel or combustion gas leaks during or after engine rebuild
- Mixing incompatible aftermarket gaskets from different sources
- Incomplete rebuild due to missing individual gaskets
📏 Specifications
- Part Name: Engine Gasket Set
- Material: Application-specific — multi-layer steel, composite and rubber seals
- Manufacturer: Kawasaki
- Condition: New — Genuine OEM
🔨 Installation
- Difficulty: Advanced (full engine overhaul)
- Tools Required: Full engine rebuild toolset, Torque wrench, Gasket scraper
- Estimated Time: Full engine overhaul — 4–8 hours
- Tip: Always consult your Kawasaki engine service manual for torque specifications and step-by-step procedures.
💪 Why Choose This Part
One kit, every seal. Save time and avoid the cost of a repeat teardown due to a missed or incorrect gasket.
🛒 Order With Confidence
✓ Genuine OEM — Guaranteed Fit — This is a genuine Kawasaki OEM part backed by the manufacturer's quality guarantee. If you have any questions about compatibility, provide your engine model and serial number and our team will confirm fitment before you purchase.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 142 reviews
Sort
Product Reviews
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024